TRANSFER GARMIN WAYPOINTS TO GARMIN HOW TO
TRANSFER GARMIN WAYPOINTS TO GARMIN SERIAL
TRANSFER GARMIN WAYPOINTS TO GARMIN SOFTWARE
TRANSFER GARMIN WAYPOINTS TO GARMIN PC
TRANSFER GARMIN WAYPOINTS TO GARMIN DOWNLOAD

In one conversion, Bishop had to cut 1,000 waypoints from 16 characters (which Raymarine allows) to 10 characters (the maximum for Garmin). There is some nuance to the export-import process. If you can save the old data on a card that is supported by the new device-meaning you have a card reader for it-the conversion process is pretty straightforward: Import the file, fix it if needed, and then export the file in the desired format. All of the waypoint data is then put into a spreadsheet-like format on the PC.Р”Р„ndren gives you a wide range of options for importing this data-Furuno, Garmin, Maptech, Northstar, Raymarine (by series), Simrad, GPX, etc.

TRANSFER GARMIN WAYPOINTS TO GARMIN PC

You click Get Waypoints, and the PC does just that, again and again.

TRANSFER GARMIN WAYPOINTS TO GARMIN DOWNLOAD

With the wiring completed, and the old chartplotter (Garmin 215, in this case) set to Data Transfer, you simply go to the Andren Tools menu, select Upload Download GPS, and select Garmin. You also will need a power supply to run the GPS. Once the wires have been identified, you interface them to the corresponding wires on your chartplotter.

TRANSFER GARMIN WAYPOINTS TO GARMIN SERIAL

In this case, the red serial cable wire is the receive data (pin 2), the orange wire is send data (pin 3), and the green wire is data ground (pin 5). To carry out an NMEA transfer, you need a good quality USB-to-serial adapter and a serial data cable with the critical wires stripped and identified. If data cards and readers are no longer available for your older system, you can usually download the waypoints using the chartplotters NMEA 0183 outputs. The first involves doing the conversion with Andren and loading the waypoints into the new system using data cards. There are two paths you can take when migrating waypoints from one system to another.

TRANSFER GARMIN WAYPOINTS TO GARMIN SOFTWARE

The software is so versatile that it even can be used to transfer the waypoints from an old Loran receiver (remember those?) to a new GPS. There are several ways to do this, but Bishop found that one of the most convenient ways to transfer waypoints was using Andren software on a PC computer. Not long ago, one of our marine electronics testers, Bill Bishop, was faced with the task of transferring the waypoints from an ancient Garmin 215 chartplotter to a newly installed Garmin 7215. I usually remove the route from my Garmin's РІР‚СљTrip PlannerРІР‚Сњ after the excursion.Photos courtesy of Andren bottom photo by Bill Bishop If you're poor like me, your Garmin may have limited memory. Personally, I usually wait until I'm close to the ghost railroad I am going to follow before turning on the trip planner. I display the route on my nuvi 2595 by selecting Apps/Trip Planner and selecting the desired route.

I've owned 3 Garmins and every one of them has been different. In this example, my Garmin nuvi 2595 is shown under the РІР‚СљDevicesРІР‚Сњ folder, so I select it and click OK. Right Click on the new route BaseCamp created and select РІР‚СљSend ToРІР‚Сњ. BaseCamp will create a highlighted route (as shown below). Select РІР‚СљCreate Route from Selected TrackРІР‚Сњ as shown belowР”Р„lmost done. Right Click on the track shown on the map Now, use BaseCamp to create the route that your Garmin can recognize.

The window will appear similar to the image below РІР‚вЂњ a bunch of waypoints and a track. In this example, I am selecting РІР‚Сљ CSX РІР‚вЂњ Monon РІР‚вЂњ Bedford to Bloomfield(1).kmz РІР‚Сњ from my Downloads folder.

Select File/'Import into my collection' from the top menu and select the downloaded kmz file. Import the downloaded kmz file into РІР‚СљMy CollectionРІР‚Сњ by: The initial window will appear similar as shown below: Many kmz files on the net do not meet this criteria, so be careful when downloading from another site.Р”В¬onnect your Garmin to your PC, wait for your PC to recognize your Garmin, and open BaseCamp. IMPORTANT РІР‚вЂњ the tracks of the kmz file must run in one direction. Go to Butch's Indiana Railroad Maps and download the desired kmz file.

Regretfully, I cannot get BaseCamp to run on Linux, but it runs great on Windows. This proved to be easy using Garmin's free software РІР‚вЂњ BaseCamp. After I created the ghost railroad routes on GE, I had to find a means of transferring routes from the GE kmz files to my Garmin nuvi 2595. It's much easier to track the route of a ghost railroad from Google Earth than tracking it from a car. Ever look for a ghost railroad while driving the backroads of Indiana and lose track where the grade went? This is the reason I created РІР‚СљButch's Indiana Railroad MapsРІР‚Сњ site. These instructions are for Ghost Railroad hunters.

TRANSFER GARMIN WAYPOINTS TO GARMIN HOW TO

How to Load a KMZ Track onto your Garmin GPS Device Using Garmin BaseCamp

Transfer garmin waypoints to garmin